点击图片查看原图
- 产地：广东
- 材质：其它
- 规格：1000 mm
| 品牌 | WEISH | 型号 | BDP-3-2135×915×3 |
| 用途 | 防火 |
不燃轻质板
不燃轻质板属于新型节能环保绿色装饰建材，经过长期，大量的市场应用，不燃轻质板因其既具硬度，更具韧性的特点不仅可广泛应用于中高档建筑的吊顶、隔墙（弧度墙）、圆(方)柱包敷、钢柱（梁）防火包敷、防火门内衬，重大长房的防火墙、幕墙内衬、大型风管、电缆桥架等，2002年起被逐步应用在建筑中的精装潢、艺术装饰、办公家具、卫生间隔断，办公隔断等，市场应用领域还在不断的扩大。
Non-combustible Lightweight Board belongs to modem energy saving green building materials for decoration. Through a long term application in bulk, Non-combustible Lightweight Board is not only used widely for the suspended ceiling, partition wall (are wall), round (quadrate) column wrap, steel column (girder) anti-fire wrap and interior liner of fire proof door of middle-top grade buildings, the fireproof wall, interior liner of curtain wall, large-sized air conduit and cable bridge frame of important workshops and so on, but also used gradually for fine decoration, art decoration, office furniture, toilet partition, office partition etc of buildings, Furthermore, its market application area is being expanded continuously.
实践证明：“不燃轻质板”是一个深受设计师、工程施工单位和用户青睬的防火、防潮、高强、隔声、环保的理想建材，可与国外同类材料媲美，是国内同类材料中的中高档品牌产品。
Practice has proved that “ Non-combustible Lightweight Board” is a sort of ideal building material with the features of fire proof, moisture proof, high strength, sound reduction and environmental protection that is deeply favored by designers, project construction units and consumers, Non-combustible Lightweight Board can match with the overseas materials of the same types and it is a sort of middle-top grade product among the domestic materials of the same types.
经上海科技情报水平检索：不燃轻质板的总体技术已达到国际先进水平。
According to the information retrieval by Shanghai science & Technique Information Center, it can be concluded that Non-combustible Lightweight Board has reached the advanced world technique standard.
技术数据Technical Data
项目Test Item | 单位Unit | 数据Data |
燃烧性能Combustibility |
| 不燃A级（GB5464）Non-combustible(A)GB5464 |
密度Density | g/cm3 | 0.9-1.15 |
导热系数Thermal Conductivity | W/(m.k) | 0.25 |
吸湿变形率Moisture Absorption | % | ≤0.28 |
抗冻性Freezing Resistance |
| 经过25次冻融循环无分现象 No delamination after 25 freezing cycles |
防霉防蛀功能Mildew &Moth Proof |
| 板为无机物具放虫防霉防蛀功能 board belongs to Inorganic materials and has these functions |
抗反卤型Impermeability | 12小时 | 无水珠、无返潮No water drop at the bottom |
抗折强度Bending Strength | Mpa | 干态16、湿态20Dry 16 Saturated 20 |
抗冲击Impact Strength | Kj/㎡ | ≥5.7 |
耐火极限Fire-resistant Limit | min | 2×6mm 60 2×8mm 120 2×10mm 180 2×12mm 240 |
隔声量Sound Reduction | db | 2×8mm 44 2×12mm 54 3×12mm 57 4×14mm 60 |
标准板长宽容差Parallel Deviation | mm | 2440×1220 5 2400×1200 5 |
标准板厚度容差Thickness Deviation | mm | 0.5 |
外观Appearance |
| 正面平整光滑反面平整不光滑 One side: Flat and smooth The other side: Flat and rough |
导静电板表面电阻率Surface Resistivity | Ω | ≤1×105-6 |
静电耗散板表面电阻率Surface Resistivity | Ω | ≤1×108-9 |
上述数据依据国家权威部门的检测报告。
不燃轻质板的安装说明
Installation Instructions for Non-combustible Lightweight Board
1、 不燃轻质板（以下简称板）的构件制作（如墙、柱、吊顶等）应在干燥的气候中进行。
2、 根据设计要求先安装好轻钢龙骨（或其他龙骨）骨架，并按施工规范检验骨架安装合格。
3、 用自攻螺丝固定板、固定顺序：
1) 划线确定固定部位：在固定部位钻预孔，孔径比自攻螺丝的直径要小1mm。
2) 用自攻螺丝固定板，先固定板的中间部位，在固定板的两边。
3) 自攻螺丝间距不大于200mm。
4) 板边距与自攻螺丝中心须大于15mm，以增加牢度。
5) 板与板之间建议不留缝。
6) 自攻螺丝头须沉入板面1mm，并要作防锈处理。
7) 建议采用专用自攻刮削螺丝，可使螺丝头经过刮削的作用一次性下沉。
4、 在板墙上粘贴瓷砖：
1) 安装工序同上。
2) 板缝用防水腻子批嵌。
3) 板面用防水涂料涂满。
4) 用U型钉将一层机制金属丝网复在墙面上。
5) 用1:2水泥砂浆刮糙至金属网平。
6) 用同样比例的水泥砂浆或专用瓷砖粘贴磁砖。
5、 欢迎电话咨询
技术服务热线020-39949995 13352880065
Welcome to use Non-combustible Lightweight Board. Please carefully read the following installation instructions:
1) Determine the fixation part by making a line, and preliminarily make boreholes on the fixation with the borehole diameter being 1mm smaller than that of the self-tapping screws.
2) Again, use the self-tapping screws to fix the board, Firstly fix the middle part of the board and then fix the both sides of the board.
3) The space between the self –tapping screws should not be more than 200mm.
4) The space between the board edge and the center of the self-tapping screws must be larger than 15mm so as to increase fastness.
5) No seam between boards is preferred.
6) The had of the self-tapping screws needs to enter into the board surface till the depth of 1mm and it is required to carry out the rust-proofing treatment for the head.
7) It is suggested to adopt special self-tapping scrape screws so as to make the screw head be settled once through the action of scraping.
- Affix ceramic tiles on a board:
1) Other installation procedures are the same as the above-mentioned ones.
2) Treat flat seams with water proof putty.
3) Fully paint the board surface with water proof paint.
4) Cover the metope with a layer of machine-made wire net and U-nails.
5) Scrape with cement-sand slurry (1:2 proportion) until the metal silk screen smooth.
6) To atlix the ceramic tiles with the same proportion of cement-sand slurry of Special ceramic tile cementing glue.
Service hotline: 020-39949995 13352880065
节能环保从www.weish.net开始，乐享低碳，超越奢华。WEISH威旭专业服务节能环保，帮助企业实现低碳经济，节能创造价值！低碳热线：4000-133-168 020-39949995 13352880065广州威旭环保科技有限公司客服QQ549555078,WEISH威旭官网:www.weish.net
